Specifications:

Stock Numbers		Dimensions - Inches
Plain Pattern	Shoulder Pattern	Shank		Eye		Overall Length Plain	Overall Length Shoulder	Maximum Shank Lengths
		Dia. & Thread	Length	I.D.	O.D.
1	21	1/4"-20	1"	3/4"	1-1/4"	2-1/4"	2-3/8"	3"
2	22	5/16"-18	1-1/8"	7/8"	1-1/2"	2-5/8'	2-3/4"	4"
3	23	3/8"-16	1-1/4"	1"	1-21/32"	2-29/32"	3-1/4"	4-1/2"
4	24	7/16"-14	1-3/8"	1-3/32"	1-27/32"	3-7/32"	3-5/8"	4-1/2"
5	25	1/2"-13	1-1/2"	1-3/16"	2-1/16"	3-9/16"	4"	4-1/2"
6	26	9/16"-12	1-5/8"	1-9/32"	2-9/32"	3-29/32"	4-1/2"	4-1/2"
7	27	5/8"-11	1-3/4"	1-3/8"	2-1/2"	4-1/4"	4-7/8"	4-1/2"
8	28	3/4"-10	2"	1-1/2"	2-13/16"	4-13/16"	5-1/4"	5"
9	29	7/8"-9	2-1/4"	1-11/16"	3-1/4"	5-1/2"	6"	5"
10	30	1"-8	2-1/2"	1-13/16"	3-9/16"	6-1/16"	7"	5"
11	31	1-1/8"-7	2-3/4"	2"	4"	6-3/4"	7-1/2"	2-3/4"
12	32	1-1/4"-7	3"	2-3/16"	4-7/16"	7-7/16"	8-1/2"	3"
14	34	1-1/2"-6	3-1/2"	2-1/2"	5-3/16"	8-11/16"	9-1/2"	3-1/2"

 

Working load limits for eye bolts are based on a straight vertical lift in a gradually increasing manner.  Angular lifts will significantly lower working load limits (see Shoulder Pattern) and should be avoided whenever possible.  If an angular lift is required, a properly seated Shoulder Pattern eye bolt must be used.  Loads should always be applied to eye bolts in the plane of the eye, not at some angle to this plane.  Angular lifts must never be more than 45º pull.  Metric Eye Bolts and stainless steel also available.

Specifications:

Diameter and Thread	Working Load Limit		Plain Pattern	Shoulder Pattern
	Straight Pull (X)	45º Pull (Y) Shoulder
1/4"-20	500	125
5/16"-18	900	225
3/8"-16	1400	350
7/16"-14	2000	500
1/2"-13	2600	650
9/16"-12	3200	750
5/8"-11	4000	1000
3/4"-10	6000	1500
7/8"-9	7000	1750
1"-8	9000	2250
1-1/8"-7	12000	2500
1-1/4"-7	15000	3750
1-1/2"-6	21000	4900

WARNING:  DO NOT EXCEED RATED CAPACITIES.  ANGULAR LIFTS SHOULD BE AVOIDED WHENEVER POSSIBLE.